Pipette Holders
HL-U: Connect to all U-type headstages

How to know which pipette holder you need:
• Is the collar (where the holder attaches to the headstage) threaded or smooth?
• If it is threaded, then you need the HL-U (most common).
• If it does NOT have threads, then Molecular Devices no longer makes electrode holders for you.
For use only with threaded headstage collets.
HL-U For 1.0-1.7 mm glass
$278.00Add to cart
HLB-U BNC adapter
$137.00Add to cart
HLR-U Right-angle adapter
$337.00Add to cart
(4) different sizes of cone washers allow the holder to accommodate pipettes with outer diameters from 1.0 to 1.7 mm. Suction port connects to 1 mm ID tubing. Low-noise easy-maintenance construction. Contains a 0.25 mm silver wire.
Spare components supplied are as follows: Cone washers (5 of each size), (4) 50 mm lengths of silver wire and 70 mm of silicone tubing to make new seals. BNC adapter accepts a BNC-type electrode holder.

Replacement Parts for HL-U Holder
Available parts:
HL-CAP Two polycarbonate caps
$82.00Add to cart
HLC-11 Orange cone washer (5 pack), 1.1 mm ID, fits 1.0 – 1.1 mm OD glass
$45.00Add to cart
HLC-13 Clear cone washer (5 pack), 1.3 mm ID, fits 1.1 – 1.3 mm OD glass
$45.00Add to cart
HLC-15 Orange cone washer (5 pack), 1.5 mm ID, fits 1.3 – 1.5 mm OD glass
$45.00Add to cart
HLC-17 Clear cone washer (3 pack), 1.7 mm ID, fits 1.5 – 1.7 mm OD glass
$45.00Add to cart
HLP-U Brass pins, 1 mm, (3 pack) for HL-U electrode holders
$55.00Add to cart
HLT-70 Silicone tubing, 1 mm ID, 70 mm long
$37.00Add to cart
HL-1 and HL-2: Connect to non-U-type CV Series headstages

For use only with non-threaded white PTFE inert collets.
HLB-1 BNC adapter – Ask
HLR-1 Right-angle adapter – Ask
HL-2-17 For 1.5-1.7 mm glass
$230.00Add to cart
Ag/AgCl Pellets and Ag Wires
For U-type and Non-U-type Holders
HLA-003 Ag/AgCl pellet assemblies, (3 pack) 1 mm diameter AgCl pellet on the end of an Ag wire. The Ag wire is insulated from the electrode solution by a wax-sealed PTFE inert tube.
$273.00Add to cart
HLA-005 Ag wires, (5 pack) Ag wires used in all holders. The 0.25 mm wires are 50 mm long.
$45.00Add to cart
Replacement Parts for HL-1 and HL-2 Holders
HLO-12 ‘O’ rings fit HL-1-12 and HL-2-12 holders (10 pack) – Ask
HLO-17 ‘O’ rings fit HL-1-17 and HL-2-17 holders (10 pack)
HLP-O General purpose 2 mm plugs (5 pack)
$45.00Add to cart
HLP-1 1 mm brass pins for HL-1 holders (3 pack)
HLP-2 2 mm brass pins for HL-2 holders (3 pack)
HLS-001 Pierced rubber seals fits HL-1 and HL-2 holders (10 pack)